November 7, 2016

 

Toshiba has developed Bluetooth® low energy [1] System-on-Chip (SoC) compliance with version 4.2 that reduce current to 50% that of current products[2] for IoT devices driven by a small-sized coin cell lithium battery. By adopting an architecture configuration and analog circuit design suited to low power operation, current consumption of 3.2 mA for receive (RX) and 3.5mA for transmit (TX)[3] are achieved, considerably lengthening battery life. The SoC also integrates RF (Radio Frequency)[4] matching networks, reducing the number of external components and contributing to downsizing of IoT devices. This technology will be presented at the 2016 IEEE Asian Solid-State Circuits Conference (A-SSCC) in Toyama, Japan, on November 8.

Recent rapid advances in IoT have realized wearable multi-functional IoT devices, such as smart watches and smart bands, that collect and manage a wide range of sensor information. Bluetooth® low energy, developed specifically for low-power wireless communications, is used in many IoT devices to cut weight and extend battery life. In general, there is a trade-off between current consumption and radio performance—receiver sensitivity and transmission power—and conventional Bluetooth® low energy SoC cannot satisfy both requirements at once. In order to use various types of usable batteries in wearable IoT devices, a Bluetooth® low energy SoC with low current consumption, in the range of 3-4mA, is a major requirement. Although it is effective to include external components in a Bluetooth® low energy SoC to shrink the size of the Bluetooth® low energy device, degradation of receiver sensitivity and transmission power of a Bluetooth® low energy SoC with built-in RF matching networks remains a problem, due to loss mismatch.

Toshiba has introduced three techniques to reduce Bluetooth® low energy SoC current consumption: (1) a receiver architecture configuration suitable for low current consumption; (2) a highly efficient power management system; and (3) low current RF design.

(1) The receiver architecture introduces a local synthesizer that employs a frequency half that of a conventional receiver, reducing current consumption in the local oscillator. Although the architecture tends to be vulnerable to interference signals because of its complex frequency configuration, a high tolerance to interference is achieved by adopting frequency planning that can avoid folding from cellular signals.
(2) In order to improve power loss in the regulators (LDO: Low Drop Out)[5], LDOs are eliminated from the SOC. As performance degradation due to switching noise from a DC-DC converter is a concern, a phase locked loop[6] is used to fix the switching frequency of the DC-DC converter and prevent interference with the band used by the Bluetooth® low energy.
(3) In low current RF design, so that TX and RX can share a single voltage controlled oscillator (VCO), the frequency tuning range of the VCO must be significantly wide, which increases current consumption. By dividing the VCO for the TX and the RX to narrow the required frequency tuning range for each VCO, low current consumption is achieved. In addition, a switching amplifier technique is introduced in the power amplifier to reduce current consumption.
By adopting these low current techniques, Toshiba’s Bluetooth® low energy SoC reduces operating current consumption, to 3.2 mA for the RX and 3.5 mA for the TX while improving radio performance; in the RX sensitivity is −93 dBm and output power 0 dBm. Furthermore, by integrating all RF matching networks in the SoC, which is fabricated with the 65 nm CMOS process, the external component count can be reduced to seven from the 19 required by Toshiba’s current product.

Toshiba will adopt this new current consumption technology in Bluetooth® low energy products scheduled to start mass production this December[7].

[1]: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG,

[2]: Compared to Toshiba’s “TC35667FTG”.

[3]: The world lowest current consumption on July 11, 2016; Toshiba survey.

[4]: Frequency used in wireless communication

[5]: A regulator that can be operated even with only a small difference in voltage between input and output

[6]: Electronic circuitry to synchronize the phase and frequency of the input and output signal by the feedback control.

[7]: Engineering samples have been available since October 2016.

*Information in this document, including product prices and specifications, content of services and contact information, is current on the date of the announcement but is subject to change without prior notice.

Toshiba Corporation- Semiconductor and Storage Products Company　Website＞
http://toshiba.semicon-storage.com/ap-en?mm=cp161108&no=02

 

 

Visit Chip1Stop Chinese site
Visit Chip1Stop Korean site
Visit Chip1Stop English site
Visit Chip1Stop German site

Companies Website:
http://toshiba.semicon-storage.com/ap-en?mm=cp161108&no=02

Toshiba News Release

• Toshiba Starts Test-Sample Shipments of a Bare Die 1200V SiC MOSFET with Low On-Resistance and High Reliability, for Use in Automotive Traction Inverters

  2024/11/13Toshiba  Automotive

• Toshiba Starts Sample Shipments of Gate Driver IC for Three-Phase Brushless DC Motors in Diverse Automotive Applications

  2024/11/01Toshiba  Automotive

• Toshiba Releases Automotive Photorelay with Output Withstand Voltage of 900V, Housed in a Small Package

  2024/10/28Toshiba  Automotive

• Toshiba’s 1200V Additions to its Lineup of Third-Generation SiC Schottky Barrier Diodes Will Contribute to High Efficiency in Industrial Power Equipment

  2024/09/26Toshiba  Power Supply

• Toshiba Is Sampling an Automotive CXPI Responder Interface IC that Contributes to Shorter Software Development Times

  2024/09/05Toshiba  Automotive

Related News Release

• STMicroelectronics releases long-range wireless microcontrollers for energy-efficient connectivity in smart metering, smart building, and industrial monitoring

  2023/12/11  STMicroelectronics  RF & Micro Wave

• STMicroelectronics reveals broad selection of antenna-matching RF integrated passive devices for STM32WL MCUs

  2023/02/22  STMicroelectronics  RF & Micro Wave

• Start Production; the NJG1186, FEM for 1.2-GHz-band GNSS

  2022/07/12  Nisshinbo Micro Devices  RF & Micro Wave

• Toshiba Electronic Devices & Storage Corporation Introduces SOI Process with Low Noise Figure for Low-Noise RF Amplifiers for Smartphones

  2018/01/29  Toshiba  RF & Micro Wave

• Toshiba Electronic Devices & Storage Corporation Launches Two New ICs Compliant with Bluetooth® Ver.5.0

  2018/01/10  Toshiba  RF & Micro Wave